Bebop Knowledge Base

Sort by:
Finding the serial number Parrot Bebop Drone's serial number is located on the battery bed.   In FreeFlight Pro, tap the drone's network name (BebopDrone-xxxxxx) to open its information page. > The serial number is listed near the bottom of the page.   The serial number of the last connected drone is displayed on FreeFlight Pro, On the main page press on the name of the drone. Firmware version, Lastest GPS coordinates, serial number, number of flights, total flying time are displayed.     With FreeFlight 3 The serial number and last GPS coordinates can be found on FreeFlight 3 app : Select Settings from the main page on FreeFlight 3 Select on "Details on the last connected drone" Make a capture of the screen with the Serial number of your drone and Skycontroller (if available)   Related content Finding the serial number Installing propellers Maintenance and repair
View full article
WIFI USE: How to respect regulations and optimize Bebop Drone range Read the original article on Parrot Blog.     Introduction: The range of Bebop Drone depends on the power of WiFi generated by the device (smartphone / tablet). This power depends on several parameters: the type of device and its use regulation indoor/outdoor setting selected channel radio/physical environment In general, it is better to use 2.4GHz WiFi to maximize range. If you want to focus on the quality of streaming video, it is recommended to choose 5GHz WiFi (less interference). The Parrot Bebop Drone software features an optimized algorithm that gives advantage to the piloting reactivity than the video streaming quality. Note that the quality of the streaming video has no influence on the quality of the video “onboard”  recorded by the drone (1080p 30fps). Protocol: To perform these tests, the experimental protocol is as follows: Bebop flies 20 m above ground Fly straightkeep heading camera forward (camera forward) Device held in its optimum position Flight in a neutral radio environment (without disturbance Wifi) Flight till disconnection During these flight test sessions, the quality of the FPV experience varies. For example, you can reach 200m and then the video streaming quality decreases and then arrive around 225 m with a better one. This variation is mainly due to the physical environment around the drone. (Field, trees, buildings …) Results The following table shows the Bebop drone’s range results (estimated or calculated) with a Bebop No. PI040339P14K005079 with the version 1.32. FreeFlight versions used for the different smartphones / tablets are for iOS 3.1.25 and for Android 3.1.28. The tests were conducted December 3rd, 2014.     *Europe includes the following countries : Austria, Belarus, Belgium, Bosnia and Herzegovina, Bulgaria, Cambodia, Croatia, Cyprus, Czech republic, Denmark, Estonia, Finland, France, Germany, Greece, Greenland, Haiti, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland, United Arab Emirates, United Kingdom Devices The maximal range reached by the Bebop Drone is highly correlated to the device (see Table above). Note that intrinsic Wifi performances of Bebop enable it to reach 2km with Skycontroller in optimal conditions. To maximize the reach with your device, Wifi antennas for your phone should be oriented to the drone (without obstacles). The position of your hands on it affects the quality of the wireless connection with your drone. Try to hold your device in one direction or the other and vary its inclination.   Skycontroller The Skycontroller * is a device, with a very specific Wi-Fi architecture, designed for the Bebop to maximize its reach. It is not compatible with AR.Drones. Tests conducted by the Skycontroller take into account the quality of the video streaming unlike other devices. The position of the hands on the Skycontroller does not affect the test results. Due to the Wifi regulation, channels at the beginning and end can not reach the maximum power.Here are the best channels with Skycontroller: Channel 6 for 2G4 Channel 44 for 5G band-1 Channel 157 for 5G band-3 The Wifi transmitter of Skycontroller is more powerful in 5 GHz than in 2.4 GHz. The power is limited following the regulations of each country. The maximum power at 2.4 GHz is about 400 mW, it is about 4W at 5 GHz on channel 157. Regulation Each Wifi device must meet the standards of the country in which it is used. This applies to your device and obviously to the Parrot products (in particluar, Bebop and Skycontroller). Each country imposes a maximum power and a set of authorized channels. (See Table below)     To perform the required network settings, go to Settings, and scroll with your finger to the Settings screen Networks Country Settings: By default, the selected setting is AUTO. Bebop Drone scans the surrounding WiFi networks and select the country it detects in the beacon frames, according to the international standard 802.11d.     When you use the Parot Bebop Drone in the US, the regulation restrains the access to the country setting.     For other countries, you can change manually the setting Indoor-Outdoor Wifi standards distinguish Indoor or Outdoor use, especially in the case of the 5GHz band. This configuration affects the number of available channels.     For some areas , the European zone, the 5GHz band (channels 36,40,44 and 48) are limited to Indoor use. They are therefore inaccessible if the Outdoor setting is selected.     If you select Indoor setting. The channels of the 5GHz band become available to the countries of the European zone. Channel selection Notable differences between the networks 2.4 GHz and 5 GHz are: The 5GHz network has a shorter range than 2.4 GHz. The devices configured in 2.4 GHz are more affected by interference than those configured as 5 GHz (which uses more bandwidth on a given channel). There are fewer devices supporting 5GHz.   Bebop embeds a channel selection optimization algorithm that will evaluate the best compromise between maximum range and quality of streaming video, while favoring the latter. The channel selection by the algorithm is correlated to the Bebop environment during Bebop boot.     The transmission power of the Bebop is the same at 2.4 GHz and 5 GHz. It is necessary to emit twice the power at 5 GHz to have the same reach than at 2.4 GHz . Ifyou want to focus on the ranfe, configure in Auto 2.4GHz:     The channels are much less congested at 5GHz. The standard for 5GHz Wifi does not extend to the adjacent channels. If you want to focus on streaming video quality, choose the configuration in Auto at 5 GHz.     You can make your setting manually. Select Manual and click on the desired channel in the dropdown list. Reminder: some channels are not available depending on your country and setting Indoor / Outdoor.     Recommendations Here are our recommendations to increase your drone range: Choose your device well and check the way you hold it, in particular the position of your hands, especially when you are at the range limit . Choose the country in which you are in the app. Respect the indoor / outdoor setting. Channel selection : if you are in the middle of many wifi networks, choose the auto -all mode. Otherwise, go auto -2,4 mode. Choose an environment with less physical obstacles as possible wether in front of you or a few meters next to you (tress, fences,..) Choose a place with the least amount of interference (other pilots, networks … ) . Stay at a minimum altitude of 5 meters. Avoid being directly above the drone. If you want to fly high, set a distance of 50m between you and the drone. At the range limit, aim your device to steer the drone and orientate he drone so that you can see its rear feet (camera forward)     The operator should keep the drone in his/her sight.
View full article
  Network Name   Change the network name of your Parrot Bebop Drone: Change the Parrot Bebop Drone  name in the Product name field. Reboot the Parrot Bebop Drone . Note: The network name of the Parrot Bebop Drone  can only contain letters, numbers and underscores ("_"). It must not exceed 32 characters in length.   WPA2   Set a password for your Parrot Bebop Drone 's Wi-Fi network.   Location   Select your country.   Wi-Fi band   Connect the Parrot Bebop Drone to the 2.4 or 5 GHz Wi-Fi bands. The 2.4 GHz Wi-Fi band enables you to fly the Parrot Bebop Drone from a greater distance. It is generally more congested than the 5 GHz Wi-Fi band in urban areas. The 5 GHz Wi-Fi band enables you to obtain a better quality connection between the Parrot Bebop Drone and your smartphone for streaming footage. Check your smartphone user guide (or the technical specifications) to see whether it supports connection to the 5 GHz Wi-Fi band. If it does not, use the 2.4 GHz Wi-Fi band only.   To switch the Wi-Fi band (2.4 GHz or 5 Ghz) manually without using the application, hold down the on/off button of the Parrot Bebop Drone for 5 seconds .   Note: The diagram at the bottom of the screen shows the state of the Wi-Fi channels.   Before flying the Parrot Bebop Drone , ensure that you comply with the Wi-Fi frequencies restrictions for the area in which you intend to fly. Certain frequencies may be restricted or forbidden. Selecting the country and activating the outdoor option enable FreeFlight Pro to adapt the available channels according to the legislation of the selected country.   For example, in certain countries using the 5 GHz Wi-Fi band may be prohibited in outdoor mode.   In automatic mode, FreeFlight Pro automatically selects a channel according to the country, the mode (outdoor/indoor), and the Wi-Fi band selected and the congestion of the channels.   If you encounter a problem with the quality level of the Wi-Fi connection: Select Manual mode. Select a non-overloaded channel using the information displayed on the diagram.
View full article
You can share flights data using social netowrks and email. To do so, you nee to register on Parrot Cloud : Academy and using a valid internet connection. There is 2 boutons "Send Piloting" / "Share" .     The data sent via email is a json file. Using third party tools like Flight Data Manager permit to process data shared.  
View full article
Question   How does Return To Home work ?   Answer   Return To Home enables you to tell the Parrot Bebop Drone to fly back to the last take-off position, or  your smartphone/tablet location if the Parrot Bebop Drone is receiving no GPS signal.   When you activate RTH, the software systematically determines which of the following data is available before directing the drone to execute a return flight.   1.  The position of the drone at the moment of take-off, if GPS is connected when RTH is activated.   2.  The position of your controlling device (smartphone/tablet, Skycontroller), if Wi-Fi is connected when RTH is activated.   3.  If there is no GPS connection at take-off, the first available GPS fix after the drone is airborne.   During RTH, the drone will fly at a speed of  24 ft/ 8 m (per sec) and a height of 60 ft/20 m, regardless of the drone's max altitude and speed settings.   *Note: RTH feature cannot be activated if neither your smartphone nor the Parrot Bebop Drone is receiving a GPS signal.   **Note: when in RTH mode, the drone will fly towards its starting point in a straight line; therefore, make sure the flight path is free of obstacles.   ***Note: To locate your position, FreeFlight Pro must have access to your device's location service.     To activate location service:   iOS Settings > FreeFlight Pro > Location service.   Android Settings > Application manager > FreeFlight Pro > Permissions.   For further information, see your device user guide.
View full article
Question What happens if I close the FreeFlight Pro App during a Flight Plan ? Answer The drone will continue its flight plan until the end.
View full article
Question Do I need to stay connected to the Bebop Drone via WiFi to execute a Flight Plan? Answer No; however, live video will only be displayed while an active WiFi connection is maintained.
View full article
Question Do I need to purchase flight plan on each of my Android or iOS devices separately? Answer No, the purchase is linked to your Apple or Google Account. You may be prompted to “Buy” the in-app purchase again, which is followed by the message below stating you’ve already purchased this. Simply press OK to access the Flight Plan features on your secondary device.
View full article
Top Contributors