Sort by:
You can plan your flights using the in-app Flight Plan, available in in-app purchase on FreeFlight Pro. *Note that you need to create and load your flight plan before taking off.     Summary   Create a Flight Plan Fly with Flight Plan     Create a Flight Plan   1. Make sure your smartphone is connected to Internet and the GPS is on. 2. In FreeFlight Pro, select Flight Plan.   *Note: you can also launch Flight Plan from the main menu by tapping  .   3. At the PRODUCT CHOICE prompt, select Disco.    >A a satellite view of your area appears.             To see the satellite view in 3D, slide two fingers upwards.    When in 3D mode, the control interface disappears. To display the controls again, slide two fingers downward to return to the satellite view.   *Note: You need an Internet connection to display the satellite view. If you want to fly in an area without Internet connection, create and save your flight plan beforehand. **Note: Make sure your flight route is located in an area unobstructed by power lines, buildings, residences, and trees.     Plan a route   Place waypoints   Waypoints help you create a precise, autonomous flight plan using Disco’s GPS feature.   *Note: Before launching Flight Plan, make sure your smart devices are connected to the internet, and turn on GPS.   To place waypoints:   1. Tap on the map to create a waypoint. > The first waypoint appears. Waypoint bubbles are solid colored when first created.    2. Tap on the map again to create another waypoint. > A line connecting the two waypoints appears.   The number at the center of the waypoint bubble indicates the drone's altitude in flight. The upper right-hand number indicates the order in which the waypoints were made: #1 is the first waypoint, #2 is the second way point, and so on. The number over the connecting line indicates the distance between two waypoints. S is the starting point, and the circle around the first waypoint means the drone will orbit over the starting point after launch. 3. Continue to make waypoints until you are satisfied with the route.  To undo last action, tap     Plan for landing After you have mapped your flight, you need to tell the Parrot Disco where and how to land.     Linear landing This is the default landing pattern for the Parrot Disco, where the drone aligns itself with a "runway" and lands like a conventional aircraft.   To set linear landing:   1. Press and hold on the last waypoint until the blue dialog box opens.    2. Select LINEAR LANDING (default) and the landing funnel graphic appears over the last waypoint.   The landing funnel depicts the amount of distance the Parrot Disco needs to land.  If necessary, zoom out to see the entire flight plan, and move the cone-by dragging the E or L bubbles-to another position on the map. (E = End point, L = Landing point)       Circular landing   During circular landing, the Parrot Disco will circle over the end point and descends in a spiral pattern.   To set circular landing:   1. Press and hold on the E button after selecting linear landing. > The blue dialog box opens.    2. Select CIRCULAR LANDING.   > The landing funnel disappears.   3. Drag the E button to relocate the landing site. The circle surrounding the button signifies the landing pattern.  Circular landing requires an area of about  240 ft./80 m free of any obstacle all around.     Editing Waypoints After you have created your route, you can go back and change various parameters of each waypoint.     Change altitude There are two ways to change the altitude of the Parrot Disco in Flight Plan:   Using the vertical slider 1. Tap a waypoint; the bubble turns solid, the blue dialog box opens, and the vertical slider becomes active.   2. Slide the button up or down to adjust the drone’s altitude. *Note: the maximum altitude is limited to 492 feet.   Using the keypad 1. Press and hold a waypoint until the blue dialogue box opens. 2. Tap EDIT to open the “WAYPOINT” dialogue screen.   3. Enter a new altitude and then tap OK.   Insert a waypoint on a line   1. Press and hold anywhere on a line where you want to insert a waypoint, and the blue dialogue box opens (notice the arrow indicating the point of insertion).    2. Tap INSERT. > A new waypoint appears.       Saving a flight plan To save a new flight plan:   1. Tap     at the upper-right corner.    2. Tap Save as on the Saved flight plans screen.   3. Use the keypad to enter a name for your flight plan and then tap Save.     Open a saved flight plan Launch Flight Plan. Tap   At the Saved flight plans screen, tap the flight plan you want to open. Tap Open   Delete a flight plan Tap   At the Saved flight plans screen, tap the flight plan you want to delete, the selected file turns blue. Tap Delete.  When the dialogue box opens, select OK to confirm, or Cancel to return to the previous screen.     Fly with Flight Plan. Make sure your Flight Plan is created and loaded. Switch on the Parrot Disco. Wait until the light turns green, indicating the GPS location is fixed. Connect your smartphone to Parrot Disco and launch FreeFlight Pro. On the main screen, press Flight Plan. Press Start. Stand facing the wind and launch the Parrot Disco into the wind. The Parrot Disco makes its way to the first waypoint and orbits 3 revolutions before starting the route you have defined.
View full article
    Landing   General guidelines   Locate a suitable landing spot prior to take-off. Always make sure you are in an area with at least 240 ft/80 m of clearing on all sides to accommodate landing.     When you are ready to land   1. Maneuver the drone into the wind (against the wind), align it with your intended landing area and start your approach.   2. As the drone descends and gets closer to the landing area, if necessary, pull back on the left stick to reduce speed.   3. When the drone is between 20 to 30 ft.(5-10 m) off the ground, press    on the Skycontroller 2 to begin auto-landing.   *Note: direction control is still available during auto-landing. **Note: pressing     again will ABORT auto-landing if the drone is still more than 30 ft/10 m above ground.   4. Parrot Disco reverses thrust to reduce speed, noses up right before touch down and lands.    ***Note: avoid over-correcting the drone during the final stage of the auto-landing sequence.    
View full article
For the best experience, use the combination of your smartphone and Parrot Skycontroller 2 to fly the Parrot Disco. Parrot Disco cannot be flown by using your smartphone alone.     STAY CLEAR OF THE MOTOR AREA AFTER TURNING ON PARROT DISCO! When not flying, disconnect battery to prevent accidental discharge.   Piloting modes   Auto-assist   Under auto-assist, Parrot Disco maintains its altitude and heading automatically, so you can enjoy the flying without having to worry about maintaining speed, adjusting control surfaces, etc.    And in case you let go of the stick momentarily, auto-assist ensures that Parrot Disco stays airborne.    Manual   This feature allows you to use an RC remote (not included) to fly the Parrot Disco. However, auto-assisted flying is not available in this mode.   *Note: in order to use a RC controller, you must first install a radio receiver (in Parrot Disco) specific to your controller.     Piloting configurations   There are three piloting configurations:   1.   Flying with Parrot Skycontroller 2 only. 2.   Flying with Parrot Skycontroller 2 and smartphone/tablet. 3.   Flying with Parrot Skycontroller 2, smartphone/tablet, and Parrot Cockpitglasses. Familiarize yourself with no. 1 and no. 2 before advancing to no. 3.     Piloting screen     Control methods   You can also customize the controls to your preference in FreeFlight Pro.     Flat trim   Flat trim resets the downward sensor to further enhance flight stability. It is recommended that you flat trim the drone prior to each flight and after a crash.   1.   Place Parrot Disco on a flat, dry surface. 2.   Press the On/Off switch to turn on the drone. 3.   On your smartphone, connect to Parrot Disco’s Wi-Fi ® : Disco_xxxxxx. 4.   In the FreeFlight Pro application, go to FLY&FILM > Setting > Position, then tap FLAT TRIM.     Take off     Disco must take off into the wind.   1.   Stand facing upwind and firmly hold the area near the nose/shoulder of the Parrot Disco with one hand.    2.  Make sure Parrot Disco’s propeller area is completely cleared of any obstacle.   3.  On Parrot Skycontroller 2, press the TAKE OFF button  . The motor runs slowly for 3 seconds before kicking into full power.   *Note: DO NOT LAUNCH until AFTER the motor fully accelerates. **Note: To stop the motor, press .   4.  A «Ready to take off» pop-up window is displayed on your smartphone. The drone is ready for take off.   5.  Holding the drone to your side, with the arm fully extended, gently toss Parrot Disco straight and upward (without twisting at the waist) into the wind. Parrot Disco climbs to an altitude of 150 feet (45 meters) and circles over its starting position in a 180-feet-diameter orbit (55 meters).   *Note: If the drone is not airborne within 10 seconds after powering on, the motor shuts off automatically .  Press   again to begin a new take-off sequence. **Note: DO NOT LAUNCH DISCO OVERHEAD!   6.  Once Parrot Disco is in stable orbit, you can take over the controls .     Return home   To recall Parrot Disco to its starting point, press the return button   on Parrot Skycontroller 2, or tap the Return Home icon     in FreeFlight Pro.   When Return Home is activated, Parrot Disco climbs (or descends) to 150 ft/50 m (default altitude) and heads for the starting position. Once there, Parrot Disco orbits overhead in a 180 ft/60 m-diameter circle at the same altitude.     Landing   Spiral   Once spiral/circular landing is initiated, Parrot Disco automatically turns into the wind to reduce landing speed on touchdown. 1.  Make sure you are in an area of at least 240 ft/80 m in diameter to accommodate the spiral pattern.   2.  Push the left control of the Parrot Skycontroller 2 to the left or to the right to set your Parrot Disco to loitering mode.  3.  On your Parrot Skycontroller 2 press    . >>Disco descends in a spiral and lands.   Linear     To land Parrot Disco in a straight-a-way fashion:   1.   Maneuver the Parrot Disco so it is flying into the wind. 2.   On Parrot Skycontroller 2, press LANDING   . >>Parrot Disco descends in a straight line, and just prior to touchdown, noses up to reduce speed and lands softly. *Note : you can still control the Parrot Disco during descent.   To abort landing, press again on Parrot Skycontroller 2. Parrot Disco climbs to loitering/standby height (50 m /150 feet) and begins circling overhead.     Flight Plan   With Flight Plan, you can pre-plan a flight by designating specific routes for Parrot Disco, and just sit back and enjoy the scenery as it soars through the air.   Flight Plan is available as an in-app purchase in FreeFlight Pro. *Note: You must create your flight plan before taking off. **Note: Parrot Disco still has to be launched MANUALLY.   Creating a Flight Plan   1.   Tap    to enable waypoint editing. 2.   On the map, tap where you want to place your first waypoint.       > A bubble with two numbers appears. The big number at the center is the altitude at which Parrot Disco will fly, and the smaller number represents the order of the waypoint. 3. Continue to place your waypoints. 4. Once you have drawn your path, press and hold the last point of your journey.     > A pop-up window appears. Select a landing mode (linear or spiral).      Spiral landing requires an area of at least 240 feet (80m) in diameter and free of obstacles. Your flight plan is created.   Flying with Flight Plan 1.   Make sure your flight plan is created and loaded. 2.   Turn on your Parrot Disco. 3.   Wait until the Parrot Disco’s warning light turns green, indicating the GPS is connected. 4.   Connect your smartphone to the Parrot Disco and start the FreeFlight Pro application. 5.   On the Home screen, press Flight Plan. 6.   Press Start. 7.   Stand facing upwind and launch Parrot Disco.       > The drone begins the course you set.   For more detail on Flight Plan, go to Flight Plan .  
View full article
Top Contributors